Hide A Hose

The new Hide a hose Valve has been made 38% smaller! Measures just 4.4 x 6.3”. Fits within a normal 2 x 4” wall. Improved door seal ensures maximum suction throughout entire Hide-a-hose system. With the "The Retractable Hose Central Vac System," the vacuum hose is stored inside the wall. Each outlet has a hose hidden within the system´s own vacuum tubing. When finished using, the suction from the central vacuum unit retracts the hose back out of sight. Then, it may simply carry your handle to the next inlet.

Dimension:  4.4 x 6.3″ (11.2 x 16.0cm)
Color: Almond

With the "The Retractable Hose Central Vac System", the vacuum hose is stored inside the wall. Each outlet has a hose hidden within the system´s own vacuum tubing. When you´re finished, the suction from the central vacuum unit retracts the hose back out of sight. Then, you simply carry your handle to the next inlet.

Since being first being introduced, Hide-A-Hose was a revolutionary idea.  Hide-A-Hose has never been a company happy with the status quo, so they are at it again with an all new valve design. This valve is smaller and features many improvements over the orginal valves.

• White Inlet Valve
• Finish Door
• Low Voltage On and Off Switch
• 4 Installation Screws
• 2 Wire Nuts

Dimension: 4.4 x 6.3in

Genuine Hide A Hose 90 Degree Sweep Elbow. These 90 degree elbows are 16” long and provide for the least possible resistance to airflow. Hide-A-Hose installations require these larger fittings to be used in order to have the vacuum hose retract back into the piping smoothly. Most Hide-A-Hose port locations utilize around 2 to 4 of these Hide-A-Hose Sweep 90’s.

The Hide A Hose Valve Rough-in Kit is the required mounting plate for all of the New HS5000 Hide-A-Hose Style Trim Kits. These Rough-in kits in conjunction with the new HS5000 Trim kit will allow for a maximum wall thickness of 1 ½” and fit within a normal 2×4” wall. To prevent the rapid flex hose from stretching and getting stuck in a standard fitting, install a reducer in the pipe run a few feet past the length of the hose.

• 1 rough in frame
• 1 rough in pipe fitting
• 1 reducer
• 1 mud cover
• 4 mud cover screws.

The Hide A Hose Stand Alone Mounting Kit is a 2-part rough in box for mounting the HS4000 central vacuum trim kit where installation in a wall cavity is not desired. Typical applications are mounting in a cabinet, closet, or on an external wall. Hide-A-Hose is usually installed in the wall, but it can be installed on the surface of the wall, or on the floor, ceiling, or on a counter. Use this box instead of a HS4000 rough-in plate. Pipe or a HAH 90 attaches to it and the HS4000 trim kit fits inside of it. The box with pipe connector is 12 inches long, 6-1/2 inches wide, and 5 inches tall. Central vac pipe fits into the connector. You will need minimum of 24 inches of depth if you lay this down in a cabinet.

Dimension: 12 x 6.5 x 5 inch

The NEW Retractable Rapidflex Hose designed for the Hide A Hose 50' Hose. These new Rapidflex hoses offer a larger diameter than the standard Hide A Hose thus increasing airflow by up to 25% – the new redesign has also made these hoses significantly easier to pull and retract. The hose is constructed with a very soft and flexible nylon, thus eliminating the need for a hose sock. Simply pull out, vacuum, and when you are finished the suction from the central vacuum unit retracts the hose back out of sight. Comes in 30’, 40’, 50’ and 60’ and can be trimmed to your needed size.

Dimension: 23.6 x 16.1 x 16.1 inches
Item Weight : 24 pounds

The NEW Retractable Rapidflex Hose designed for the Hide A Hose 40' Hose. These new Rapidflex hoses offer a larger diameter than the standard Hide A Hose thus increasing airflow by up to 25% – the new redesign has also made these hoses significantly easier to pull and retract. The hose is constructed with a very soft and flexible nylon, thus eliminating the need for a hose sock. Simply pull out, vacuum, and when you are finished the suction from the central vacuum unit retracts the hose back out of sight. Comes in 30’, 40’, 50’ and 60’ and can be trimmed to your needed size.

Dimension: 23.6 x 16.1 x 16.1 inches
Item Weight : 24 pounds

The NEW Retractable Rapidflex Hose designed for the Hide A Hose 30' Hose. These new Rapidflex hoses offer a larger diameter than the standard Hide A Hose thus increasing airflow by up to 25% – the new redesign has also made these hoses significantly easier to pull and retract. The hose is constructed with a very soft and flexible nylon, thus eliminating the need for a hose sock. Simply pull out, vacuum, and when you are finished the suction from the central vacuum unit retracts the hose back out of sight. Comes in 30’, 40’, and 50’ and can be trimmed to your needed size.

Dimension: 23.6 x 16.1 x 16.1 inches
Item Weight : 24 pounds